PRODUCTS / AMERICAN / EUROPEAN BRAND SPECIALIZED TOOLS / HARLEY-DAVIDSON / HARLEY-DAVIDSON(102)

 
Model 14-K1013
Item Name Balancer Bearing Service Tool Kit
Descriptions Ideal tool to remove and install outer balancer bearing on the chain guide support plate safely.<br> Also installs the new balancer bearing and counter balancer shaft on Twin Cam 96 or 110 B Softail engines.<br> <br> Fits 2007 to Present FXST.<br> Taiwan Pat.<br>
 
Model 14-K1014
Item Name Ignition Switch Connector Remover Tool
Descriptions Ideal tool to remove the ignition switch wiring connector.<br> <br> Fits FL Touring models on 2003 to 2013 that have a H-D No.61530-03B Ignition Switch.<br>
 
Model 14-K1015
Item Name Top Dead Center Tool
Descriptions Fits: All Sportster Motors, All Big Twins
 
Model 14-K1016
Item Name Oil Pump Seal Installer
Descriptions Ideal tool to install oil pump seal below gear surface for a no-leak fit.<br> <br> Fits all Big Twin aluminum oil pumps 1968-Present. (except Twin Cam).<br>
 
Model 14-K1017
Item Name Rocker Box Alignment Tool Set
Descriptions Idea tool screw to allow precise alignment of twin cam rocker boxes to avoid improper sealing surface issues and rocker arm interference problems.<br> <br> Fits any Twin Cam Rocker Box Covers from 1999 to present.
 
Model 14-K1018
Item Name Wrist Pin Lock Ring Tool
Descriptions Ideal tool to install spiral-lock type wrist pins without distorting ring.<br> <br> Fits wrist pin size 0.515 inch inner diameter.<br>
 
Model 14-K1018A
Item Name Wrist Pin Lock Ring Tool
Descriptions Ideal tool to install spiral-lock type wrist pins without distorting ring.<br> <br> Fits wrist pin size 0.535 inch inner diameter.<br>
 
Model 14-K1019
Item Name Hollow Axle Plug Tool
Descriptions Ideal tool to align rear axles, providing the correct center point required for safe vehicle alignment. <br> Lube the O-ring ends and insert in left to right ends of the axle.<br> <br> Fits 2008 to present hollow rear axle model Sportsters, Dyna, and Softail.<br>
 
Model 14-K1020
Item Name Hose Repair Kit
Descriptions Hose barbed end is .3125 (5/16”), thread end is 12mm x 1.25. It can be used with either a .250” or .3125” hose.<br> <br> Fits all the 12mm spark plug threads on all Twin Cams, XL 1986 and later, as well as Screamin’ Eagle EVO BT heads.<br>
 
Model 14-K1021
Item Name Crankshaft Bushing Remover/Installer Tool
Descriptions Ideal tool to remove and install the crankshaft bushing in the support plate on a Twin Cam. <br> Fits on all twin cam.<br>
 
Model 14-K1022
Item Name 6-Speed Main Drive Gear Bearing Tool
Descriptions Ideal tool to install the two bearings and seal in the main drive gear.<br> <br> Fits all 2006 to present Dyna and 2007 to present FL & FXST.<br>
 
Model 14-K1023
Item Name Magnetic Tappet Holder Tool Set
Descriptions Ideal tool to hold the tappets in the tappet bores when changing or servicing cams.<br> <br> Magnets will magnetically hold the tappet in place while performing any cam chest work when installing the tool over the tappet cover, a time saver tool.<br> <br> Fits Harley-Davidson Twin Cam and Milwaukee Eight engines.<br>
 
Model 14-K1024
Item Name Piston Pin Bushing Tool Set
Descriptions Ideal tool to remove and install wrist pin bushing without removing rods from crankcase.<br> <br> Fits Harley-Davidson all Twin Cam 1999-2006.<br>
 
Model 14-K1025
Item Name Balancer Shaft Bearing Remover and Installer Set
Descriptions Ideal tool to remove and install Balancer Shaft Bearings.<br> <br> Fits Harley-Davidson all Twin Cam 88™ Balanced Engines.<br>
 
Model 14-K1026
Item Name Valve Spring Compressor Tool Set
Descriptions Ideal tool set to compress valve springs for removal or installation. Included collars for Conical Valve Springs and Milwaukee Eight Valve Spring. <br> <br> Fit most Big Twin and XL models, new Milwaukee Eight series engine.
 
Model 14-K1026A
Item Name Valve Spring Compressor Tool
Descriptions Ideal tool to compress valve springs for removal or installation.<br> <br> Fit most Big Twin and XL models.<br>
 
Model 14-K1027A
Item Name 10mm/12mm Cylinder Head Holding Tool
Descriptions Ideal tool to hold the cylinder head that you are servicing.</br> The 12mm end is for Twin Cam two valve heads while the 10mm end is for Milwaukee Eight four valve heads.</br> </br> Fits both Twin Cam and Milwaukee Eight cylinders.
 
Model 14-K1027B
Item Name 12mm/14mm Cylinder Head Holding Tool
Descriptions Ideal tool to hold the cylinder head that you are servicing.</br> </br> Fits H.D. 1948-2013
 
NEW
Model 14-K1033
Item Name Oil Filter Wrench
Descriptions Fits '21-later Revolution Max engine-equipped models.
 
Model 14-K395
Item Name Wheel Bearing Removal/Installation Tool
Descriptions It can be used on 3/4"and 1"I.D. bearings 2000-2006 and 25mm bearings on most 2007-2008 models with or without ABS.